Getting Started with Plumber's Essentials for Bathtub Installation
Getting Started with Plumber's Essentials for Bathtub Installation
Blog Article
Have you been searching for tips on Installing A Bathtub?
Installing a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult project. If the old tub is readily obtainable, the task can relocate rapidly; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. See to it you have certified on your own for the job as well as are comfortable trying it. Rather than employing a professional to take over a halfway-completed job, it is far better to think about using one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This article will aid you install a new bathtub in your washroom if you have already acquired a brand-new bathtub and also don't need to change the setup of your previous water supply pipelines.
Your tools and also product checklist ought to comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome because of the restricted accessibility that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind should be attached to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using both wooden boards under its feet, put the bathtub in the called for position. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub till the level reads level.
To mount faucets, fit all-time low of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water and check all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has been used at the very least once as this will certainly resolve it right into its final placement.
Planning for the Setup
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, causing complications with dampness and possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealant can break rather very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very fascinated with Tools You Need to Install a New Bathtub and I really hope you enjoyed reading the entry. Are you aware of somebody who is curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Feel free to share it. Thank you for your time. Kindly visit our blog back soon.
Professional touch for plumbing woes. Report this page